土工膜焊接粘接是整個施工中重要的工序，如果出現問題，會直接影響整個工程的質量和進度，甚至會造成很大的經濟損失和社會影響。因此我們要嚴抓施工質量，對于符合土工膜焊接粘結在施工過程中可能會發生的一些問題進行分析指定施工質量標準，驗收實施方案和現場的施工記錄，以便有效對土工膜焊接粘結的施工質量。小編為您介紹影響土工膜焊接粘結施工質量的因素：

　　1、溫度因素

　　土工膜焊接粘結，受大氣溫度影響不大，在正常氣溫5-35℃均可進行，大氣氣溫過低或者過高時容易影響焊縫質量。焊縫及施焊溫度宜為250-350℃(選擇溫度從低溫到高溫慢慢調節，以確保焊接效果，施焊錢必須試焊，以確定焊機溫度及行走速度)。

　　2、風力因素

　　一般土工膜焊接粘結在風力較平穩的狀態下進行(一般在5級以下)，如果風力過大容易影響土工膜焊接粘結進程，導致整條焊縫焊接粘結失敗。

　　3、濕度影響

　　土工膜表面必須干燥，不能有水分，如有水珠就影響膜與膜的焊接粘結，使焊縫質量達不到要求。因此土工膜焊縫也有濕度要求。比如早上有露水，你用手一摸土工膜，上面有水珠，就不能進行焊接粘結，得用干布擦甘以后或者風干后在進行焊接粘結。再比如說降霜時也得等土工膜干燥后再進行焊接粘結。

　　4、其他因素

　　首先就是土工膜焊接粘結時，土工膜上不能有灰塵，如有必須用毛巾擦掉;其次就是土工膜下邊必須平整，不能影響焊縫機的行走速度;第三就是土工膜施焊的熟練成都也決定土工膜的焊縫質量。